Washer - Dryer Motor Windings Clean | Western Appliance Repair Meridian

Cleaning Washer and Dryer Motor Windings:

Most trouble with Washer and Dryer motor windings can be blamed on dirt, grease, and moisture which create such an undesirable conduction medium which may result in a breakdown of insulation.  Dirt and grease collected on the inner and outer surfaces of electrical units prevent proper circulation of air and conduction of heat to the outer surfaces and air.  This could cause the appliance motor to overheat and decrease the life of your appliance.  It is, therefore, very important that all accumulations of dirt, grease, and moisture be removed.  The best means of cleaning motors and generators are air pressure, vacuum suction, and grease solvents.

Air pressure, reversing a vacuum cleaner and blowing dust off the windings is the most satisfactory device.

Vacuum suction, use a vacuum cleaner or hose to remove grit, carbon, iron, and copper dust.  Be sure the hose is not made of metal.

Rich - Western Appliance Repair Meridian Idaho

Automatic Washing Machines - Western Appliance Repair Meridian Idaho

Automatic washers offer various cycles of operation.  Provisions for soaking, rates of agitation, lengths of washing time, rates of spinning, and kind and number of rinses differ among models such as whirlpool, kenmore, maytag, and ge.  Here, however, are the basic operations common to all automatic washers.

Soaking clothes in a washer:
In some washing machines, separate user settings are provided for a soak cycle.  The clothes are agitated about in warm or cold water in the same manner as for washing.  Water is extracted and drained at the end of the soak cycle.  The user setting may have to be reset to start the regular washing machine cycle.  If there is not a user control setting for soak, the wash setting can be used with warm water, and after the water has be drained, the setting will be reset for the regular wash cycle.

Western Appliance Repair Meridian
email
Meridian, Idaho 83642
208-599-1086
http://www.western-appliance.com

Washer Electrical System - Washer Timers

Some of the parts in a automatic washing machine appliance, new and old, include timers, solenoids, switches, motors, pumps, and motors. 
The most important, or the "brains" behind all the operations performed is the washer timer.  The timer programs the other electrical components in such a manner as to control the mechanical functions, water fill system, dispenser, drain, agitate, and spin.  There are also different modes of timer control such as Delicate, Permanent Press, Second Rinse, Normal Wash, Pre-wash, and Pre-soak.  These merely identify the various cycles available and the setting of the timer to obtain those cycles.  Timer settings require the operator to set it manually and select and set the wash and rinse water temperatures.  Some of the more modern Front Load Washers, have sensing features that choose load size, wash time, and spin time automatically.

For more appliance repair articles in Meridian and Boise Idaho, please visit our website at http://www.western-appliance.com
You can also email Western Appliance Repair

Dishwasher Repair - Soft Water | Dishwasher Repair Meridian

Soft water, as used in dishwashers, is virtually mineral free.  Total dissolved solids are usually low, in the range of 100 to 200 ppm.  Water is considered soft when the grain hardness does not exceed 4 grains/gal.
In naturally soft water the temporary hardness, or bicarbonate content, is the important factor affecting the Ph.  Solutions of bicarbonate, when heated to a high temperature, undergo a chemical reaction to form a carbonate.  In the presence of hardness, the carbonate with the calcium and magnesium, precipitates out of solution as scale.  In soft water this precipitation does not take place, and the carbonate stays in the solution.  Carbonate is much more alkaline than bicarbonate, causing the alkalinity of the final rinse water in a dishwasher to increase.  The carbonate and bicarbonate content of water is part of the total dissolved solids.  Most naturally soft water will have some calcium and magnesium dissolved in it, even though the amount may be small.

Many appliance repairs in Boise, Meridian, and Eagle areas of Idaho have to do with white scaling found on glassware and dishes.  In the majority of these dishwasher calls the problem lies with the hard water that is being used to clean the dishes.  If you suspect you may have hard water the best cure would be to invest in a good water softener.  This will help your dishwasher clean better and it will minimize the white scale you see on your dishes.

Another Tip from Western Appliance Repair Meridian and Boise.  You can contact us at 208-599-1086 or Email Me .

Refrigerator Door Seals Replacement | http://www.western-appliance.com

Refrigerator Door Seals Diagnosis and Repair
Refrigerator door seals may be one of the most misunderstood parts of the refrigerator.  Ask a layman or do-it-yourselfer about why his refrigerator is not functioning or warming properly and the first thing he may say after “I don’t work on compressors” is “but let’s check the door seals."   The door seals rarely go bad or have a problem over the lifetime of the refrigerator.  The only door seals I’ve seen go bad are when dogs or cats chew or sharpen their claws on them, or kids that like to climb or hang on the refrigerator door.  A really bad door seal problem is most likely to show up as a defrost problem or frost buildup on the interior of the freezer.  This is due to humid air getting into the refrigerator.
Door seals are magnetically held to the door frame to keep the doors closed.  Unless the seal is shredded or you can physically see a gap between the seal and the door frame with the door closed, there is no reason to suspect a door seal problem.
To replace the refrigerator door seal, you should have a nut driver of the proper size.  A cordless drill-driver is better choice.  A magnetic tip will prevent you from going crazy trying to hold the driver, the screw and the seal at the same time and allow you to complete the job faster.  There are lots of screws holding the seal on so be prepared.  Remove the screws from no more than two sides at a time.  One side at a time is better.  The idea is to prevent the plastic inner door liner from drifting around.  If you have to re align it, it can be a long, frustrating process.  The new seal will fit in the same way as the old one came out.
You are much more likely to have a door alignment issue or warping.  There’s not much you can do with a badly warped refrigerator door except to try to warp it, or bend it, back into shape or replace it.
With the door closed, measure the gap around it, top and bottom, left and right.  Check if the door edges and the refrigerator edges are parallel.  If the measurements indicate that the door is badly out of alignment, re align it by loosening the hinges slightly and shifting the door around.  It may take a few tries to get it aligned properly.
Remove anything that might be obstructing the door seals.  Sometimes the kick plate or drawer will get in the way.  If it’s metal, you may be able to bend it slightly to solve your problem.
For more information on this appliance repair articles please visit our website.  For Appliance Repair needs in the Boise, Meridian, Nampa, Eagle, Kuna, Star areas please visit our homepage or call us at 208-599-1086.

Refrigerator Defrost System | Method of Operation

http://www.western-appliance.com
Refrigerator Defrost System
When opening the refrigerator and freezer doors repeatedly to add and remove food you also let warm moist air enter the interior compartment.  The humidity from this warm air gets attracted the refrigerator evaporator coils and will freeze directly to the coils.  This will form a uniform frost layer to the outside of coils.  If too much frost builds up on these coils, airflow will be restricted and the evaporator cannot absorb heat from the interior compartment.  The result will be the freezer operating at a lower temperature and a partial or full restriction in cold air flow to the refrigerator.
To prevent too much frost from collecting on the evaporator coils, a self-defrosting refrigerator will actually stop itself for approx 20 minutes every six to twelve hours to melt off this frost.  This defrost cycle is switched off and on by an electric defrost timer or electronic ADC board.  The timer stops the compressor and switches current to an electric defrost heater located directly beneath most evaporator coils.  When the heater is energized the heat is radiated upwards to melt the frost.  The frost water drains into a pan located at the bottom of the evaporator and is diverted through a tube into little pan which is located on the bottom of most refrigerators.  Most Maytag, Kenmore, Whirlpool, GE, and Frigidaire models will have this type of system. The condenser fan circulates warm air across the water filled pan and evaporates the drain water before the next defrost cycle.
If all the frost melts before the defrost timer finishes the defrost cycle, a terminating thermostat, or bimetal, will keep the defrost heater from overheating the evaporator compartment. When the freezer compartment reaches a fixed temperature, the terminating thermostat will open the circuit and shut off the electricity to the defrost heater.
Many of the later electronic refrigerators incorporate an electronic device called an adaptive defrost control board.  This electronic control board provides the same function of the defrost timer but adds a new element to save energy and to adjust the defrost cycles to “adapt” to customer usage.  The adaptive defrost board monitors how many times the door is opened and closed.  The more the refrigerator doors are opened and closed, the more humidity has entered the compartment.  The more humidity that has entered the refrigerator the more frost that has accumulated thus the “period” between each defrost cycle will be reduced.
For refrigerator repair boise needs, whether it be Whirlpool, Kenmore, GE, Maytag, or Frigidaire, please contact Western Appliance Repair. We offer the following services:
Appliance Repair Meridian Idaho
Appliance Repair Kuna Idaho
Appliance Repair Star Idaho
Appliance Repair Eagle Idaho
Appliance Repair Boise Idaho
208-599-1086

Appliance Repair Meridian | Washing Machine Washer Hoses

http://www.western-appliance.com
When installing any washer or washing machine hose, be sure it is not twisted or kinked or positioned in such a manner that it might kink in the future and stop the proper flow of water. Most hoses used inside washers and washing machines are secured on each end by hose clamps, and easily removed and replaced by using a screwdriver, hex driver, or special hose clamp pliers.
Water Inlet Hoses
Extreme care should be taken when attaching the water inlet hoses to the washer inlet valves with nylon bodies. Cross threading of these hose couplings on the valve inlets can cause leaks and can damage the threads. Do not over tighten. A filter washer screen is provided for each hose and is to be installed cup side up in the shoes end that is to be attached to the faucet. A standard rubber washer is provided for use in the end that attaches to the valve. Two 3/8 inch inside diameter rubber molded or reinforced stainless hose is used to carry the water from the water supply valve to a water inlet valve of washing machine.
Fill Control Hose
The fill control hose and recirculation inlet hose are secured to the tub by special internal retaining rings that can be removed by use of regular or needle-nose pliers. The reducing connector that couples the fill control hose to the plastic tubing should be tightly secured to the inside of the fill control hose by use of rubber cement.
Recirculation Hoses
On many washers here are two hoses used to recirculation the water from the outer tub through the recirculation pump and through the filter at the top of the tub. The hose between the tub and the pump is attached to a plastic side outlet assembly which is secured to the tub side by a locking ring. The other hose runs from the outlet of the recirculation pump to the filter housing. Because the filter housing is secured to the top, the recirculation hose must be removed to raise the top for servicing.
Pump Outlet Hose
On machines that do not have a two-way valve, the hose runs from the pump outlet to a hole in the rear of the cabinet and is secured to a hose coupling by a hose clamp. On machines equipped with a two-way valve, the hose runs from the pump outlet to the inlet on the two-way valve.

For all your appliance repair needs choose Western Appliance Repair in Meridian Idaho. We provide the following services:
Appliance Repair Boise - We provide appliance repair throughout the treasure valley and includes garden city and hidden springs areas.
Appliance Repair Meridian - Our appliance repair in Meridian is second to none. As our home base, we can get to the job quickly and get your appliance running properly.
Maytag Repair Washer and Refrigerator Repair Experts.
208-599-1086